How to Install a Dog Door in a Block or Brick Wall
Share
Quick answer: Yes, you can put a dog door in a block or brick wall. The inside is cut the same way as any framed wall. The outside takes a diamond blade, a rotary hammer and some patience. Here's the method our installers use, what to watch for, and when to call a pro.
A JGM wall mount dog door installed in a red brick wall
JGM Pet Doors has been building and installing pet doors in Phoenix since 2009, through every kind of wall Arizona homes have. Our Wall Mount Dog Door ships anywhere in the U.S. and works in block, brick, brick veneer, stucco and wood-frame walls with siding. If your wall is stucco, see our stucco wall guide.
What you'll need
Your JGM Wall Model comes with the template, tunnel, drain pan, carpet and screws. You'll also need:
Before you order: size and wall thickness
Measure your dog standing up. For height, measure from the floor to the top of the shoulders and add 1 to 2 inches. For width, measure the widest part of the body and add 1 to 2 inches. Sizes run from Small (7" x 11") to Jumbo (16" x 30"). See our sizing guide.
Measure from the inside face of the drywall to the outside face of the block or brick. Masonry walls are often thicker than framed walls. The Wall Model comes with an 8" tunnel, with 12" and 16" tunnels available. If your wall is thicker than 12", contact us before ordering.
Step-by-step installation
Prepare the work area
Lay drop cloths inside and outside where you'll be working. Put on safety glasses, gloves and an N95 mask before you start cutting.
Choose the location
- Stay at least 14" away from doors and large windows.
- Avoid placing the door below a window if you can.
- On block walls, avoid the bond beams.
- Avoid load-bearing studs and utilities like water, gas and drain lines.
- Outside, avoid spots under a downspout or where water collects.
Mark and cut the inside wall
Place the template on the inside wall, on top of the baseboard or at the height you want. Level it and trace the outline. Cut the drywall along the line with a drywall saw.
If there's insulation behind the drywall, move it aside or take it out and set it aside to reuse later.
Drill pilot holes to the outside
With the ¼" × 14" masonry bit, drill a pilot hole from the inside through to the outside at each of the four corners of the opening.
Mark the outside
Outside, place the template using the four pilot holes as your guide. Level it and trace the outline. Where you can, line up the cuts with the mortar joints.
Cut the outline
Run the diamond blade along the marked lines. Start with a shallow pass to get the lines straight, then make a couple more passes to cut as deep as the blade allows. Don't force the saw.
If the circular saw can't finish the corners all the way through, use a Sawzall with a carbide or diamond blade to complete them.
Break out the opening
Make extra vertical and horizontal cuts across the inside of the opening with the diamond blade, dividing it into smaller sections. Then use a rotary hammer with a chisel bit to push into those cut lines and chisel the pieces out, working until the opening is through to your outline on all four sides.
Hollow block cores: leave them as they are once the hole is cut. If there was insulation in the wall, put it back around the opening so there are no gaps.
Size the tunnel
Measure the wall thickness from the inside surface to the outside surface. With tin snips, cut the tunnel to 3/8" less than that measurement. JGM recommends ordering a pet door with a 12-16" tunnel for block or brick walls.
Install the inside frame and tunnel
From inside the house, insert the inside frame and tunnel into the opening. Remove the security cover from the door and set it aside.
Install the drain pan
From outside, apply silicone and install the drain pan on the bottom of the tunnel. The side tabs face up, and the flashing edge goes down over the outside wall. Seal around the edges of the drain pan with a waterproof sealant.
Install the outside frame
Fit the outside frame into the tunnel. Use adjustable clamps to press the inside and outside frames together against the wall. Drive the included ½" screws through the pilot holes into the tunnel to pull the frames together.
At the bottom center of the frame, drive two ¼" screws into two of the three pilot holes. They shouldn't go through the tunnel. They make a small dimple that works as a drain.
Seal the outside frame
Tape off a ¼" gap between the frame edge and the wall, then caulk the frame edge with a waterproof sealant such as silicone or elastomeric.
Install the carpet
Measure the tunnel between the inside and outside frames, cut the carpet to fit, and glue it to the tunnel with siliconized latex painter's caulk.
Finish up
Clean the flaps and frame, adjust the magnets so the flaps close flat, and clean up the work area.
Common mistakes to avoid
✕ Pushing hard when drilling through brick veneer. Go slow so pieces of the veneer don't break loose.
✕ Cutting a brick in half horizontally. Follow the mortar joints where you can.
✕ Trying to cut full depth in one pass. Start shallow to get straight lines, then go deeper.
✕ Breaking out the middle without extra cut lines. Divide the opening into smaller sections first so the chisel doesn't crack the wall around it.
✕ Putting the door too close to a door or window. Stay at least 14" away, and avoid placing it under a window.
✕ Cutting the tunnel to the wrong length. Measure the wall and cut the tunnel 3/8" shorter.
✕ Caulking the bottom of the frame shut. Leave the 2" drain gap so water can get out.
When to call a pro
Block walls sometimes have cells filled with concrete or steel rebar. If you're worried about what's inside your wall, or you'd rather not cut the outside yourself, call a professional in your area.
In the Phoenix and Tucson areas, our licensed team offers professional installation. Outside our service area? Call us at (602) 738-3667 and we'll do our best to point you in the right direction.
Frequently asked questions
Do I need to fill the hollow cores in a block wall?
No. Leave the hollow cores as they are once the opening is cut. If the wall had insulation, put it back around the opening so there are no gaps.
Is it different for brick veneer?
The process is mostly the same. Drill the pilot holes slowly without pushing hard, so pieces of the veneer don't come loose. Cut through the veneer slowly with the diamond blade, and finish the corners with a Sawzall and a carbide or diamond blade if needed.
Will water get in around the door?
Not when it's installed correctly. The drain pan and its flashing edge direct water out over the wall, the frame is sealed with waterproof caulk, and a small gap at the bottom center lets any water that gets into the tunnel drain out.
What if I hit rebar or a solid-filled cell?
If you're worried about what's inside your wall, stop and call a professional in your area. In Phoenix and Tucson, call us at (602) 738-3667.
Which tunnel length do I need?
Measure your wall from the inside surface to the outside surface. The Wall Model comes with an 8" tunnel, with 12" and 16" options. For walls thicker than 12", contact us before ordering.
Ready to get started?
Built in Phoenix with dual insulated flaps, a magnetic weather seal, a metal wall tunnel and a locking cover.
Shop the Wall Model Call (602) 738-3667Not sure which size or tunnel you need? We're here Monday through Saturday, 8am to 5pm Arizona time.